FAQ

Green pollution of rendered façades is pollution caused by algal growth or fungal attack. This pollution is an undesirable and yet natural phenomenon linked to the ageing of a façade, which occurs when certain conditions favourable to the proliferation of algae are met. In essence, it is an aesthetic problem and has no negative impact on the building itself or the health of the occupants.

Benefit from financial support of up to 50% of the investment cost!

Under Article 4(h) of the Law of 31 May 1999, as amended, establishing a fund for the protection of the environmental, municipal administrations, municipal associations and public bodies under the supervision of the municipalities may receive aid covering up to 50% of the investment cost for projects for the rational use of energy and the promotion of new and renewable energy sources. This financial aid is accessible to all municipalities, regardless of their commitment to the climate pact.

Within the framework of the building permit application procedure, it is not within the municipalities’ field of competence to monitor compliance with private property boundaries. The right of ownership is a fundamental right enshrined in the Constitution, therefore any encroachment of the façade insulation (considered as a fixed element of the building) on a neighbouring private property must be covered by the transfer of a real right over the plot of land in question, otherwise there is a risk of legal recourse within 30 years of the work being carried out (acquisitive prescription in real estate matters).

In the context of the building permit application procedure, it is necessary to respect the municipal planning regulations relating to setbacks from neighbouring private properties. The same provisions apply to constructions along the municipal public domain.

As is the case for buildings along the municipal public domain, buildings along the State road (national road and State-managed road) must, within the framework of the building permit application procedure, comply with the municipal urban planning regulations on setbacks.

For constructions located in the vicinity of the State public domain at a distance of 25 metres from a national road (N) or at a distance of 10 metres from a State-managed road (CR), established from the property line, a road permit is required from the Minister of Sustainable Development and Infrastructure. As part of a road permit, provisions regarding the setbacks of buildings in relation to the road will be applied. These may differ from the setbacks set by the municipalities.

With regard to building permits, the municipalities systematically check that buildings are set back from the municipal public domain or plot boundaries.

As a rule, the planning regulations for setbacks are regulated by the municipalities in their General Development Plan (Plan d’Aménagement Général, PAG) or in the Special Development Plans (Plans d’Aménagement Particulier, PAP).

For municipalities whose PAG has not yet been adapted to include current legislation, the planning regulations relating to setbacks are still included in the written part of the PAG or in the building regulations. For these municipalities, the measurement of setbacks in the event of energy retrofitting is set out individually, by municipality, in those documents.

On the other hand, for those municipalities whose PAGs have been completely revised since 2011, the Grand Ducal Regulation that is the basis for the applicable definitions provides that the building setbacks are to be measured without the additional insulating layer in the case of an energy retrofit.

In both cases, the municipalities can include derogation mechanisms in their regulations in order to promote energy retrofitting, for example through a reduction in the minimum setback to be observed.

In principle, a wall does not breathe. Air renewal and moisture removal are only achieved by ventilation (via windows or a mechanical ventilation system). The effect of 'breathing' as mentioned above refers to the transfer of moisture by the diffusion of water vapour. In practice, this is minimal and does not play any role in the removal of moisture. On the other hand, it is important for interior plaster to be able to absorb moisture from the air and release it back into the interior after ventilation. The moisture regulation effect therefore only operates within the first few centimetres (on the interior side) of a wall. For example, clay plaster on internal walls provides excellent moisture regulation.

It is often façade insulation systems that are implicated and pilloried for this. It is true that on insulated walls the outer render layer has a lower temperature and slows down the drying of rainwater and condensed water. However, in order to determine the origin of the spread of micro-organisms, various factors have to be taken into consideration: weathering, orientation, proximity of trees or bushes and the lack of protection provided by protruding building elements (roof overhang, window sill, projection, eaves, etc.).

For new builds, weather protection should ideally be provided from the outset. Similarly, by opting for a thicker finishing coat, higher surface temperatures can be obtained.

On the contrary! Poor quality sealing can result in significant amounts of energy loss. However, the risk of building deterioration is an even greater factor: in winter, warm, moist air escapes to the outside through leaky areas such as joints and cracks. In this way, the air cools down and moisture condenses, which can lead to the formation of mould in the cavities. In most cases, we don't even notice it and therefore we can't react.

Airtightness is therefore a key issue. You must ensure that your house is well ventilated, either simply by opening the windows or by installing a controlled ventilation system.