FAQ

In all cases, a properly executed energy retrofit improves the energy efficiency of the building and helps to reduce dependence on higher energy prices by reducing energy consumption for heating. In order to guarantee the sustainability of a dwelling and to maintain/increase its value, its maintenance and modernisation need to be considered in view of the long term. Whereas some retrofitted elements might depreciate in 10 or 20 years, for other elements this can happen much faster. To learn more about the potential for improving the energy efficiency of your home, request a free energy assessment with a Klima-Agence adviser.

Various State and municipal aid is also available to help finance your energy retrofitting project.

Calculation of the environmental indicators is directly linked to calculation of the thermal transmittance U and its inherent calculation rules. However, the layers of membranes and seals, which are negligible when calculating the thermal transmission coefficient given their low impact in terms of their insulation capacity, should be taken into consideration for calculation of the predicted environmental indicators.

The values of the I_eco12 indicator are provided for some commonly used insulation materials in Chapter 7.3 of the Annex to the Grand Ducal Regulation on the Certification of the Sustainability of Housing and can be reused.

In the event that other insulation materials are used, experts can calculate the I_eco12 indicator using the I_calc calculator, which can be viewed online 

The I_eco12 indicator is used to assess new insulation installed on an existing building and is taken into consideration in the following cases:

• in the case of sustainable energy retrofitting of elements of the thermal building envelope under the Klimabonus subsidy scheme;
• as part of the LENOZ certification of an existing retrofitted building.

With regard to building permits, the municipalities systematically check that buildings are set back from the municipal public domain or plot boundaries.

As a rule, the planning regulations for setbacks are regulated by the municipalities in their General Development Plan (Plan d’Aménagement Général, PAG) or in the Special Development Plans (Plans d’Aménagement Particulier, PAP).

For municipalities whose PAG has not yet been adapted to include current legislation, the planning regulations relating to setbacks are still included in the written part of the PAG or in the building regulations. For these municipalities, the measurement of setbacks in the event of energy retrofitting is set out individually, by municipality, in those documents.

On the other hand, for those municipalities whose PAGs have been completely revised since 2011, the Grand Ducal Regulation that is the basis for the applicable definitions provides that the building setbacks are to be measured without the additional insulating layer in the case of an energy retrofit.

In both cases, the municipalities can include derogation mechanisms in their regulations in order to promote energy retrofitting, for example through a reduction in the minimum setback to be observed.

In principle, a wall does not breathe. Air renewal and moisture removal are only achieved by ventilation (via windows or a mechanical ventilation system). The effect of 'breathing' as mentioned above refers to the transfer of moisture by the diffusion of water vapour. In practice, this is minimal and does not play any role in the removal of moisture. On the other hand, it is important for interior plaster to be able to absorb moisture from the air and release it back into the interior after ventilation. The moisture regulation effect therefore only operates within the first few centimetres (on the interior side) of a wall. For example, clay plaster on internal walls provides excellent moisture regulation.

It is often façade insulation systems that are implicated and pilloried for this. It is true that on insulated walls the outer render layer has a lower temperature and slows down the drying of rainwater and condensed water. However, in order to determine the origin of the spread of micro-organisms, various factors have to be taken into consideration: weathering, orientation, proximity of trees or bushes and the lack of protection provided by protruding building elements (roof overhang, window sill, projection, eaves, etc.).

For new builds, weather protection should ideally be provided from the outset. Similarly, by opting for a thicker finishing coat, higher surface temperatures can be obtained.

On the contrary! Poor quality sealing can result in significant amounts of energy loss. However, the risk of building deterioration is an even greater factor: in winter, warm, moist air escapes to the outside through leaky areas such as joints and cracks. In this way, the air cools down and moisture condenses, which can lead to the formation of mould in the cavities. In most cases, we don't even notice it and therefore we can't react.

Airtightness is therefore a key issue. You must ensure that your house is well ventilated, either simply by opening the windows or by installing a controlled ventilation system.

The heat transmission coefficient (known as the U-value) determines how much heat passes through a building element – the lower the value, the better the insulation. Therefore, for example, a sand-lime brick wall with a thickness of 50 cm has a U-value of about 1.0 to 2.0 W/m² K. With an outer insulation thickness of 12 cm to 30 cm, the walls of well-renovated buildings today achieve U-values between 0.3 and 0.1 W/m² K.