FAQ

In the context of the building permit application procedure, it is necessary to respect the municipal planning regulations relating to setbacks from neighbouring private properties. The same provisions apply to constructions along the municipal public domain.

As is the case for buildings along the municipal public domain, buildings along the State road (national road and State-managed road) must, within the framework of the building permit application procedure, comply with the municipal urban planning regulations on setbacks.

For constructions located in the vicinity of the State public domain at a distance of 25 metres from a national road (N) or at a distance of 10 metres from a State-managed road (CR), established from the property line, a road permit is required from the Minister of Sustainable Development and Infrastructure. As part of a road permit, provisions regarding the setbacks of buildings in relation to the road will be applied. These may differ from the setbacks set by the municipalities.

With regard to building permits, the municipalities systematically check that buildings are set back from the municipal public domain or plot boundaries.

As a rule, the planning regulations for setbacks are regulated by the municipalities in their General Development Plan (Plan d’Aménagement Général, PAG) or in the Special Development Plans (Plans d’Aménagement Particulier, PAP).

For municipalities whose PAG has not yet been adapted to include current legislation, the planning regulations relating to setbacks are still included in the written part of the PAG or in the building regulations. For these municipalities, the measurement of setbacks in the event of energy retrofitting is set out individually, by municipality, in those documents.

On the other hand, for those municipalities whose PAGs have been completely revised since 2011, the Grand Ducal Regulation that is the basis for the applicable definitions provides that the building setbacks are to be measured without the additional insulating layer in the case of an energy retrofit.

In both cases, the municipalities can include derogation mechanisms in their regulations in order to promote energy retrofitting, for example through a reduction in the minimum setback to be observed.

• Demolition: sale of a ruin or a building that does not have a heating installation and which will be demolished after purchase.
• Inheritance or gift.

• New building: any building that is subject to a building permit application. (A feasibility study concerning the use of renewable energies should be appended to the building permit application.)
• Extension of an existing building.
• Modification of an existing building (building permit required), if the surface area of the modified element of the thermal envelope exceeds the surface area of the same existing element (walls, windows, roof, etc.) by 10% and if the modification has an impact on the energy performance of the building. (Issuance of an energy performance certificate for the new planned situation.)
• Substantial alterations to an existing building (without a building permit), if the surface area of the altered element of the thermal envelope exceeds the surface area of the same existing element (walls, windows, roof, etc.) by 10% and if the alteration has an impact on the energy performance of the building. (Issuance of an energy performance certificate for the new planned situation.)
• Change of owner or tenant.
• Demolition: sale of a building that will be demolished after purchase, if the building has a heating installation, exterior walls and a roof.
• Modification of technical facilities, if the modifications of these technical facilities exceed €1,500 (for a single-family house) or €3,000 (for a multi-family house).

The energy performance certificate is a regulatory obligation, therefore no subsidy is provided for its establishment.
The energy performance certificate is issued according to precise rules set out in the amended Grand Ducal Regulation of 30 November 2007 on the energy performance of residential buildings. It is valid for 10 years from the day of its issue. The issuance of an energy performance certificate and the information it contains shall not result in any direct obligation for energy retrofitting.

The energy performance certificate (EPC) or energy passport is the quality label that defines the energy performance of a residential building. The certificate provides information on the energy efficiency of residential buildings and thus allows comparisons to be made with other residential buildings. Thus, even without technical knowledge, the consumer can assess the energy quality of a residential building.

In principle, a wall does not breathe. Air renewal and moisture removal are only achieved by ventilation (via windows or a mechanical ventilation system). The effect of 'breathing' as mentioned above refers to the transfer of moisture by the diffusion of water vapour. In practice, this is minimal and does not play any role in the removal of moisture. On the other hand, it is important for interior plaster to be able to absorb moisture from the air and release it back into the interior after ventilation. The moisture regulation effect therefore only operates within the first few centimetres (on the interior side) of a wall. For example, clay plaster on internal walls provides excellent moisture regulation.

It is often façade insulation systems that are implicated and pilloried for this. It is true that on insulated walls the outer render layer has a lower temperature and slows down the drying of rainwater and condensed water. However, in order to determine the origin of the spread of micro-organisms, various factors have to be taken into consideration: weathering, orientation, proximity of trees or bushes and the lack of protection provided by protruding building elements (roof overhang, window sill, projection, eaves, etc.).

For new builds, weather protection should ideally be provided from the outset. Similarly, by opting for a thicker finishing coat, higher surface temperatures can be obtained.